Document Page: First | Prev | Next | All | Image | This Release | Search
File: 011696_103_6_021.txt
UH-1 ...
Protective Covers Fix
CW3 Charles McConkey of Colum- 0 Bend the end of the bolt about 45
bus, Ott, submitted a good idea as a degrees.
Tool Improvement Program Sugges- 0 Sharpen the end of the roll pin.
tion (TIPS).
The ziplock seal on the bugs of his Roll pin Two edg" of
Hucys protective covers would not plastic seat
F stay sealed in met cold weather.
m He tried using safety wirc to keep
TS 43-0209 Color and Marking of Military Vehicles, Allievels the seal fmm opening, but the proce-
Equipment durc look too much time. He'd make
TB 43-0213 Corrosion Prevention and Control All levels a hole in the plastic with an awl, but
TB 746-95-1 Color, Marking and CimouflagO Pattern PalntIN All levels when he pulled out the awl,.Ehc hole
forarmsment Command Equlpjmnt would close up.
T8750-10 PsInUng, Replating and Preserving lndmcuon$ All levels So he made a lool that works much L
foroommunicagonsSeCuiltyEqulpment better than an awl and cuts the time in To use the tool, hold the seal together
MIL@53M Chemlc$lApntRes@@allng (CARC) G@t halt. Herc's what you need: and push the roll pin ihmugh both
Sy*temAppllcstlonPrmduresondOuathy 0 A V4-in diameter bolt 6 inches pieces of plastic.
ControllnspecUon long Insert a 6-in piece of safety wirc
ML-T-704 TreatmentandPainflngotMatedet G@ 0 A 3h@in diafneter roll pin thrnugh the center of the rnli pin and
MIL@171 FinishingotWoodandMetalSuftm GS/Depot llcm'% lu)w you make it: ptill out the ii)c)l. letiving tlw wirc
-STD.le$ ProtWW&FlnlshlngtorkMyMlssileW"W Gseepot 0 Drift a Y,4-in diameter hole mar thn)ugh the plzi.%tic. I'wi%t the wirc
Systems the end of the bolt. tight.
M1L-ml93 PaintProcOuresandM$rkingfOrVehiclu, G@pot 0 Insert the roll pin. No more pmblenis with the %cals!
Construction Equipmentand Material
Handling Equipment
PAL-STD-194 SystemforP&Intlng and Finishing FlwUntrot G@t
Material CH-47D.Aiithorifi'Covers
MIL 2 I&nUncaftnMitrWngotcombataWT@l
TransportVehicies There's more to replacing Integrated lowii'oon@ actuators Om,
MIL-STD-1473 StandardGeneraiRequiremlstor0dorand G@t your CH-47D's than @ the eye In Task 7-io2 or TM 55-152@
MorkingotArFnyM&terlel 240-23-6. Any time you replace actuators, YOU Marc to remove the
ANL-rA6l66 Cost[ng,AI(phatiopolyurethane, Chomicaf G@pot authority coven from the old actuators and Install them on the new.
ApntR"Istlint ones. Removiog and reinstalling authority covers Is explained In
Coating,Allpho0c Polyurethow, Single G@pot Task 7-86.
Componon%ChemicsIAgentReslstsnt
If you need copies of the specifications for a specific paint or solvent, check
Appendix A or TM 43-0139. OCT 89 39
Box ID = BX000000
Unit = VII CORPS
Parent Organization = ARCENT
Folder Title = PORT OPERATIONS CARC PAINTING POLICY
Subject = ARMY REGULATION 11-34 (RESPIRATORY PROTECTION PROGRAM
Document Number = 103
Image file name = 00000105.tif
Document Page: First | Prev | Next | All | Image | This Release | Search